User ManualBusiness SolutionsEGS Smart Switch Series8-Port Gigabit SwitchesEGS2108P | EGS2110P | EGS5110Pversion 1.0
10Connecting the Switch to a NetworkDiscovery in a Network with a DHCP ServerUse this procedure to setup the Switch within a network that uses DHCP.1.
11Discovery on a Network without a DHCP ServerThis section describes how to set up an EnGenius Gigabit PoE or PoE+ Smart Switch in a network without a
12Use this procedure to access the management interface throughaWebbrowserfordeviceconguration.1. Open a Web browser on your computer and ente
13Chapter 2 Management
14 The navigation pane at the left of the web browser interface contains a System tab that enables you to manage your EnGenius Smart Switch with featu
15IP SettingThe IP Setting screen contains elds for assigning IPaddresses.IPaddressesareeitherdenedasstaticorareretrieved using
16Port SettingsUse the Port Setting to congure the speed and duplexsettings of each port.To access the page, click Port Setting under the s
17PoE ManagementThe PoE Management screen contains system PoE information for monitoring the current power usage and assign the total amount of power
18PoE Port CongurationThe PoE Port Conguration screen contains system PoEinformationforenablingPoEonthedeviceandcongureper port Po
19User Power Limit: Set the maximum amount of power that can be delivered by a port.Note: The User Power Limit can only be implemented whentheClass
2IMPORTANTTo install your Switch please refer to the Quick Installation Guide included in the product packaging.
20Cable DiagnosticsThe Cable Diagnostics setting provides information about where connectivity may have failed on the Ethernet cable. The tests use
21Zero CongurationThe Bonjour Zero-Conguration networking architectureprovides support for publishing and discovering TCP/IP-based services on
22The L2 Feature menu enables port trunking, control of multicast trafc ooding, port mirroring, cabling loopdetection and MAC address table m
23IGMP SnoopingInternetGroupManagementProtocol(IGMP)Snoopingisafeature that allows a Switch to forward multicast trafcintelligently
24Port MirroringPort Mirroring monitors and mirrors network trafc byforwarding copies of incoming and outgoing packets from one port to a mon
25Loopback DetectionUse the Loopback Detection function to congure thesystem to shut down the current port once the port is found in a loop.
26Static MAC AddressThe Static Addresses screen contains a list of static MAC addresses. Static Addresses are added and removed from the Static Addres
27VLANA VLAN is a group of ports that form a logical Ethernet segment on an Ethernet switch. VLANs let you segment your network through the switch’s m
28Adding, Editing, and Deleting Items in the ListToaddanitemtothe802.1Qlist,followthesesteps:1. Click the Add button .2
29PVIDWhen an Untagged packet enters a Switch port, the PVID (PortVLANID)willbeattactedtotheuntaggedpacketandforwardedtoaVLANspeciedI
3Chapter 1 Product Overview ... 4 Introduction/Package Contents ... 5
30Port-based VLANA port-based VLAN is a group of ports on a Gigabit Ethernet Switch that form a logical Ethernet segment. Each port of a port-based VL
313. Click the Member Ports text box to show the ports dialog box.4. Select a port to add it to the Port-based VLAN.5. Click Conrm to accept t
32QoSThe QoS enables trafc to be prioritized, excessivebroadcastand multicasttrafc tobe avoidedand overallbandwidth to be limited o
33CoS Priority ClassWithoutCoS,mosttrafcreceivedbyaSwitchisforwardedwith the same priority it had upon entering the switch. In manycases,
34Storm ControlThe Storm Control feature provides the ability to control the receive rate of broadcast, multicast, and unknown unicast packets. Stor
35Bandwidth ControlTheBandwidthControlallowsnetworkmanagerstodenethebandwidthsettingsforaspeciedport’stransmittingand receiving data
36Chapter 3 Maintenance
37Maintenance functions are available from the maintenance bar. Maintenance functions include: saving congurationsettings,upgrading rmware,
38Upgrading WARNING!Backupyourcongurationinformationbefore upgrading to prevent loss of setting information.Follow this procedure to upgrade the
39RebootingFollow this procedure to reboot the Switch.1. Click to start the reboot process.2. When a prompt displays, click OKtoconrmth
4Chapter 1 Product Overview
40 Appendix
41Federal Communication Commission Interference StatementThis equipment has been tested and found to comply with the limits for a Class B dig- ital de
42Industry Canada StatementThis device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) T
43FOR MOBILE DEVICE USAGE Radiation Exposure Statement This equipment complies with IC radiation exposure limits set forth for an uncontrolled environ
44Europe – EU Declaration of ConformityThis device complies with the essential requirements of the R&TTE Directive 1999/5/EC. The following test m
45This device is a 5GHz wideband transmission system (transceiver), intended for use in all EU member states and EFTA countries, except in France and
46Français [French] Par la présente [nom du fabricant] déclare que l’appareil [type d’appareil] est conforme aux exigences essentielles et aux autres
5Maximum data rates are based on IEEE 802.3ab standards. Actual throughput and range may vary depending on distance between devices or trac and bandw
6Environment & Mechanical: Temperature Range Operating: 32 to 104°F / 0 to 40°C Storage:-40to158°F/-40to70°CHumidity(non-condensing)
7Physical InterfaceDimensions and WeightsDesktop Design: EGS2108P & EGS2110PWeight: 1.39 lb.Width:9.45” Length:4.13” Height:1.06”Dimensions a
88 RJ-45 LAN Ports: 10/100/1000 Mbps RJ-45 LAN ports. 9 LAN Mode LED (Per Copper Port): Light off = No link is established on the port; Solid Amb
9Each EnGenius Gigabit PoE or PoE+ Smart Switch features an embedded web interface for the monitoring and management of your device. Management Interf
Commentaires sur ces manuels