EnGenius ESR-9753 Manuel d'utilisateur

1 ESR-9753 Wireless Broadband Router Ultra Speed (IEEE 802.11 b/g) User Manual Version: 1.0

10 7 Setup LAN, WAN LAN connection: Connect Ethernet cable between your PC/Notebook LAN port & one of the 4 available LAN ports on ESR-9753.

11 8 PC Network Adapter setup (Windows XP) • Enter [Start Menu]  select [Control panel]  select [Network]. • Select [Local Area Connectio

12 • Select [Internet Protocol (TCP/IP)] =>Click [Properties]. • Select the [General] tab. a. ESR-9753 supports [DHCP] function, please

13 9 Bring up ESR-9753 Connect the supplied power-adapter to the power inlet port and connect it to a wall outlet. Then, ESR-9753 automatically en

14 STEP 4 Insert the ESR-9752 CD into your DVD/CD drive and SMART WIZARD should run automatically with a few seconds. If not, please open W

15 Setup Wizard Click <Next> to proceed. Click <Exit> to abort.

16 ESR-9753 should be setup as depicted above. Make sure your DSL/CABLE modem is setup and working. Else take the help of your internet service prov

17 Check power connection for modem as well as ESR-9753. Make sure the antenna is connected to rear panel of ESR-9753. Click <Next> to proceed

18 User name and password are admin/admin. Click <OK>. Your default browser will connect to ESR-9753 Web Server http://192.168.0.1 .

19 Click <Next> to enter mode selection. Select the mode that ESR-9753 is going to be and set its configurations. AP Repeater mode does not e

2 TABLE OF CONTENTS 1 INTRODUCTION ...

20 You could choose your service type or select Others to setup WAN configurations manually. Smart Wizard has detected DHCP client. Configure the ho

21 Enter the name for your wireless network (SSID) and security key Click <Next> to proceed To apply the entire configuration, click <Reb

22 11 Initial Setup ESR-9753 ESR-9753 uses web-interface for configuration to be accessed through your web browser, such as Internet Explorer or F

23 3. Click <OK> to navigate into ESR-9753 configuration home page. 4. You will see the home page of ESR-9753 as follows.

24 12 AP Router Mode  System - Status This page allows you to monitor the current status of your router. System: You can see the Uptime, hard

25 LAN Settings: This section displays the Broadband router LAN port’s current information. It also shows whether the DHCP Server function is enabl

26 - LAN The LAN Tabs reveals LAN settings which can be altered at will. If you are an entry level user, try accessing a website from your browser.

27 DHCP Server DHCP Server: This can enable or disable the Dynamic Pool setting. Lease time: This is the lease time of each assigned IP address.

28 - Schedule This page allows users to set up schedule function for Firewall and Power Saving .

29 Edit schedule options to allow configuration of firewall and power savings services. Fill in the schedule and select type of service. C

3 Revision History Version Date Notes 1.0 November 18, 2008 Modified from existing UM.

30 The schedule table lists the pre-schedule service-runs. You can select any of the schedule record using the check box. - Event Log View operat

31 - Monitor Show histogram for network connection on WAN, LAN & WLAN. Auto refresh keeps information updated frequently. - Language This Wi

32  Wizard Click Wizard to configure the Broadband Router. Setup wizard will now be displayed; check that the modem is connected

33  INTERNET - Status This page shows the current Internet connection type and status - Dynamic IP Use the MAC address when registering for In

34 - Static IP If your ISP Provider has assigned a fixed IP address, enter the assigned IP address, Subnet mask, Default Gateway IP ad

35 Login / Password: Enter the PPPoE username and password assigned by your ISP Provider. Service Name: This is normally optional. Maximum Transm

36 Click <Apply> to save configuration and connect to ISP provider.  Wireless Settings - Basic In basic setting page, you can set wireless

37 2.4 GHz(B): If all your clients are 802.11b, select this one. 2.4 GHz(N): If all your clients are 802.11n, select this one. 2.4 GHz(B+G): E

38 - WDS with AP Router Wireless Distribution System, a system that enables the wireless interconnection of access point, allows a wireless

39 - Advanced This tab allows you to set the advanced wireless options. You should not change these parameters unless you know what ef

4 1 Introduction Congratulations on your purchase of ESR-9753 Wireless Network Broadband Router. ESR-9753 is compatible with 802.11g & 802.11b

40 DTIM Period: Enter a value between 1 and 255 for the Delivery Traffic Indication Message (DTIM). A DTIM is a countdown informing clients of the n

41 - Security This Access Point provides complete wireless LAN security functions, included are WEP, IEEE 802.1x, IEEE 802.1x with WEP, WP

42 Enable 802.1x Authentication IEEE 802.1x is an authentication protocol. Every user must use a valid account to login to this Access Point b

43 Authentication Type: There are two authentication types: "Open System" and "Shared Key". Both AP and wireless client mu

44 WPA-Radius Encryption Wi-Fi Protected Access (WPA) is an advanced security standard. You can use an external RADIUS server to authenticate

45 - MAC Address Filtering This wireless router supports MAC Address Control, which prevents unauthorized clients from accessing your wirele

46 - Wi-Fi Protected Setup (WPS) WPS is the simplest way to establish a connection between the wireless clients and the wireless router. You don’t h

47 WPS: Check the box to enable WPS function and uncheck it to disable the WPS function. WPS Current Status: If the wireless security (encry

48 - Client List This WLAN Client Table shows the Wireless client associate to this Wireless Router. - Policy The Broadband router can allow you

49  Firewall Settings The Broadband router provides extensive firewall protection by restricting connection parameters, thus limiting

5 2 Key Features Features Advantages Incredible Data Rate up to 150Mbps** Heavy data payloads such as MPEG video streaming IEEE 802.11b/g Complia

50 - Demilitarized Zone (DMZ) If you have a client PC that cannot run an Internet application (e.g. Games) properly behind the NAT firewall, then y

51 - Denial of Service (DoS) The Broadband router's firewall can block common hacker attacks, including Denial of Service, Ping of Death, Port

52 - MAC Filter If you want to restrict users from accessing certain Internet applications / services (e.g. Internet websites, email, FT

53 Add PC MAC Address Fill in “LAN MAC Address” and <Description> of the PC that is allowed / denied to access the Internet, and then click &

54 - IP Filter Enable IP Filtering: Check to enable or uncheck to disable IP Filtering. Deny: If you select “Deny” then all clients will be

55 - URL Filter You can block access to some Web sites from particular PCs by entering a full URL address or just keywords of the Web site. Ena

56 Remove URL Keyword If you want to remove some URL keywords from the "Current URL Blocking Table", select the URL keyword you wan

57  Advanced Settings - Network Address Translation (NAT) Network Address Translation (NAT) allows multiple users at your local site to access th

58 - Port Mapping Port Mapping allows you to re-direct a particular range of service port numbers (from the Internet / WAN Port) to a particular LA

59 Add Port Mapping Fill in the "Local IP", “Protocol”, “Port Range” and "Description" of the setting to be added and then click

6 3 Package Contents Open the package carefully, and make sure that none of the items listed below are missing. Do not discard the packing materia

60 Enable Port Forwarding: Enable or disable Port Forwarding. Description: The description of this setting. Local IP / Local Port: This is the LAN

61 - Port Triggering (Special Applications) Some applications require multiple connections, such as Internet games, video Conferencing, Internet tel

62 Popular Applications: This section lists the more popular applications that require multiple connections. Select an application from

63 - Application Layer Gateway (ALG) You can select applications that need ALG support. The router will let the selected application to correctly p

64 Enable/Disable UPnP: You can enable or Disable the UPnP feature here. After you enable the UPnP feature, all client systems that support

65 Priority Queue This can put the packets of specific protocols in High/Low Queue. The packets in High Queue will process first. Un

66 Bandwidth Allocation: This can reserve / limit the throughput of specific protocols and port range. You can set the upper bound and Lower bound.

67 Disabled: This could turn off QoS feature. - Routing You can set enable Static Routing to let the router forward packets by your routing polic

68  TOOLS Settings - Admin You can change the password required to log into the broadband router's system web-based management. By d

69 Remote management This allows you to designate a host in the Internet the ability to configure the Broadband router from a remote site. Enter th

7 4 Product Layout

70 - Time The Time Zone allows your router to reference or base its time on the settings configured here, which will affect functions such a

71 Synchronize with PC You could synchronize timer with your Local PC time. PC Date and Time: This field would display the PC date and time. Da

72 - DDNS DDNS allows you to map the static domain name to a dynamic IP address. You must get an account, password and your static domain

73 - Power Saving power in WLAN mode can be enabled / disabled in this page. - Diagnosis This page could let you diagnosis your current ne

74 - Firmware This page allows you to upgrade the router’s firmware. To upgrade the firmware of your Broadband router, you need to downl

75 - Back-up This page allows you to save the current router configurations. When you save the configurations, you also can re-load the saved confi

76 - Reset You can reset the broadband router when system stops responding correctly or stop functions.

77 13 Repeater Mode Repeater mode has limited settings compared to the AP mode. Choose “Repeater mode” on the top right corner of the co

78 WLAN Settings: Wireless configuration details such as SSID, Security settings, BSSID, Channel number, mode of operation are briefly shown

79 802.1d Spanning Tree: This is disabled by default. If 802.1d Spanning Tree function is enabled, this router will use the spanni

8 LED Description POWER Lights up when powered ON. Blinks on TEST/RESET WLAN Lights up in ORANGE when WLAN is enabled. Blinks on traffic LAN

80 - Event Log View operation log of ESR-9753. This page shows the current system log of the Broadband router. It displays any event occurred after

81 - Monitor Show the network packets histogram for network connection on WAN, LAN & WLAN. Auto refresh keeps information updated frequently.

82  Wireless -Basic You can set parameters that are used for the wireless stations to connect to this router. The parameters include Mode, E

83 Site Survey: You can scan the current Wireless Access Point and connect on it. -Client List This WLAN Client Table shows the Wireless client

84 -Policy The Broadband router can allow you to set up the Wireless Access Policy. Communication between Wireless clients: Allow Wireless

85  Tools - Admin You can change the password required to log into the broadband router's system web-based management. By def

86 Remote management This allows you to designate a host in the Internet the ability to configure the Broadband router from a remote site. Enter th

87 - Time The Time Zone allows your router to reference or base its time on the settings configured here, which will affect functions such a

88 Synchronize with PC You could synchronize timer with your Local PC time. PC Date and Time: This field would display the PC date and time.

89 - Power Saving power in WLAN mode can be enabled / disabled in this page. - Diagnosis This page could let you diagnosis your current

9 5 Network + System Requirements To begin using the ESR-9753, make sure you meet the following as minimum requirements:  PC/Notebook.  Opera

90 - Firmware This page allows you to upgrade the router’s firmware. To upgrade the firmware of your Broadband router, you need to download the fir

91 - Back-up The page allows you to save (Backup) the router’s current configuration settings. When you save the configuration setting

92 - Reset You can reset the broadband router when system stops responding correctly or stop functions.

93 Appendix A – FCC Interference Statement Federal Communication Commission Interference Statement This equipment has been tested and found to com

94 Appendix B – IC Interference Statement Industry Canada statement: This device complies with RSS-210 of the Industry Canada Rules. Operation is